Landoll 5211 Grain Drill User Manual Page 74
- Page / 78
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
5-2 F-725-1213 Edition
TROUBLESHOOTING GUIDE
SECTIONS PLANTING AT DIFFERENT
RATES
Seed rate adjustment not the same on all
sections
Adjust seed rate.
Drive types (sprocket ratio) not the same
on all sections
Change to same drive type on all sections.
Seed meter out of adjustment Reset seed meters.
Seed rate adjustment handle out of
adjustment
Reset seed rate adjustment handle.
Opener seed tube plugged Clean out seed tube.
Broken seed meter Allows excessive seeding - repair seed
meter.
UNEVEN SEED SPACING Excessive field speed Reduce field speed.
Unclean seed Use clean seed
Build up of seed treatment in seed cup Clean out seed meters
Seed tubes sagging Replace seed tube
Drive type (sprocket ratio) too slow Use faster drive type and readjust seed
meter opening.
Plugged opener seed tube Clean out bottom of seed tube.
OPENER DISCS NOT TURNING FREELY Opener plugged with mud/dirt Clean opener.
Scraper set too tight Adjust scraper (See “Opener Scraper
Adjustment” on page 4-27.)
Soil control strip set too tight against
opener blades
Adjust soil strip
Soil strip plugged with residue Adjust soil strip closer to blade, move
metal backing strip away from edge of
soil strip (See “Opener Soil Strip
Adjustment” on page 4-28.)
PRESS WHEELS NOT COMPACTING
THE SOIL AS DESIRED
Opener down pressure set too low Increase air system pressure on row units
(See “Air System Pressure” on
page 4-9.)
Incorrect press wheel depth adjustment Reset press wheel depth adjustment (See
“Opener – Press Wheel Adjustment”
on page 4-26.)
PRESS WHEEL OR OPENERS
PLUGGING
Backed up with openers in the ground Clean out opener and press wheels and
check for damage.
Scraper worn or not adjusted correctly Replace or adjust scraper
Opener blades worn, pinch point too wide Reset pinch point, replace worn out
blades.
Planting conditions too wet Wait until drier weather
Opener bearing failure Replace opener bearings
AIR SPRING LEAKING AIR Air spring not set all the way forward or
backward in adjustment slots
Replace and reposition air spring
Operating with too low air pressure Minimum air system pressure is 15 psi
(See “Air System Pressure” on
page 4-9.)
Broken air spring stud Replace air spring, maximum stud torque
30 ft-lbs.
AIR SYSTEM LEAK - FAST Broken or pinched air line Check hitch and wing hinge areas for
broken or pinched air line.
Broken fitting Repair fitting
Air line disconnected Reconnect air line.
Air spring has hole Replace air spring.
PROBLEM PROBABLE CAUSE SOLUTION
- Model 5211 1
- Grain Drill 1
- Operator’s Manual 1
- Table of Contents 3
- 5 Troubleshooting Guide 4
- Introduction 5
- Understanding Safety 6
- Statements 6
- Standard Specifications 7
- IMPORTANT 8
- STANDARD SPECIFICATIONS 10
- LANDOLL CORPORATION 10
- Assembly Instructions 23
- ASSEMBLY INSTRUCTIONS 24
- Press Wheel Assembly 25
- Installation (Option) 27
- Small Seed Attachment 27
- Operation and Maintenance 31
- Tractor Preparation 32
- Grain Drill Preparation 32
- Attaching Grain Drill To The 33
- Transport Locks 34
- Leveling the Hitch Clevis 35
- Transporting the Grain Drill 36
- OPERATION AND MAINTENANCE 37
- Compressor Operation 38
- Air System Pressure 39
- Hydraulic Lift System 40
- Seed Meter Gate Adjustment 42
- Seed Rate Adjustment 43
- Meter/Seed Rate Handle 44
- Adjustment 44
- Seed Rate Calibration 46
- FRONT OF SEED BOX 47
- FERTILIZER OPENINGS 47
- Fertilizer Box – Clean Out 49
- Fertilizer – Rate Adjustment 50
- Fertilizer – Rate Calibration 51
- Small Seed Rate Adjustment 52
- Small Seed Meter 53
- Assembly/Adjustment 53
- Air Spring Adjustment 54
- Opener Blade Adjustment 55
- Opener – Press Wheel 56
- Opener Scraper Adjustment 57
- Opener Soil Strip Adjustment 58
- Walkboard 59
- Ladder Use and Transport 60
- Requirements 60
- Hydraulic Row Marker Disc 62
- Adjustment (Option) 62
- Coulter Hitch (Option) 63
- 3 Point Hitch (Option) 64
- Wheel Bearing Maintenance 65
- Hydraulic Maintenance 66
- PARKING STAND 68
- 5210-jackstand down 68
- Lubrication Maintenance 70
- Chapter 5 73
- TROUBLESHOOTING GUIDE 74
Related products and manuals for Special machinery Landoll 5211 Grain Drill
(34 pages)© 2020, manymanuals.com. All rights reserved. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals